The University of Waikato - Te Whare Wānanga o Waikato
Home Waikato Home > Science & Engineering > Research Staff + Student Login

Research Publications for Leandro Bolzoni

Research is a vital function of the Waikato's School of Science and Engineering. There are many active research groups within the School, spanning a wide range of topics.

Author's Publications

Publications ByBOLZONI, Leandro

  Use our Online Phonebook to contact our current staff members.

  • Alshammari, Y., Jia, M., Yang, F., & Bolzoni, L. (2020). The effect of α+ β forging on the mechanical properties and microstructure of binary titanium alloys produced via a cost-effective powder metallurgy route. Materials Science and Engineering A, 769. doi:10.1016/j.msea.2019.138496

  • Bolzoni, L., Raynova, S., & Yang, F. (2020). Strengthening mechanisms of Ti via Al addition. Journal of Alloys and Compounds, 820. doi:10.1016/j.jallcom.2019.153447

  • Raynova, S., Collas, Y., Yang, F., & Bolzoni, L. (2020). Correction to: Advancement in the Pressureless Sintering of CP Titanium Using High-Frequency Induction Heating (Metallurgical and Materials Transactions A, (2019), 50, 10, (4732-4742), 10.1007/s11661-019-05381-z). Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. doi:10.1007/s11661-019-05586-2

  • Alshammari, Y., Yang, F., & Bolzoni, L. (2019). Mechanical properties and microstructure of Ti-Mn alloys produced via powder metallurgy for biomedical applications. Journal of the Mechanical Behavior of Biomedical Materials, 91, 391-397. doi:10.1016/j.jmbbm.2018.12.005

  • Zhang, S. Z., Liu, J. W., Zhao, Q. Y., Zhang, C. J., Bolzoni, L., & Yang, F. (2019). Microstructure characterization of a high strength Ti–6Al–4V alloy prepared from a powder mixture of TiH2 and 60Al40V masteralloy powders. Journal of Alloys and Compounds. doi:10.1016/j.jallcom.2019.152815

  • Zhao, Q., Yang, F., Torrens, R., & Bolzoni, L. (2019). PM versus IM Ti-5Al-5V-5Mo-3Cr Alloy in Mechanical Properties and Fracture Behaviour. Materials Research, 22(suppl 2). doi:10.1590/1980-5373-mr-2018-0739

  • Yang, F., Pi, Z. Q., Zhao, Q. Y., Raynova, S., Liu, Q., Sharp, K., . . . Qian, M. (2019). Strong and ductile Ti-6Al-4V alloy produced by hot pressing of Ti-6Al-4V swarf. JOM, 71(3), 1056-1061. doi:10.1007/s11837-018-3301-6

  • Zhao, Q., Yang, F., Torrens, R., & Bolzoni, L. (2019). Comparison of the cracking behavior of powder metallurgy and ingot metallurgy Ti-5Al-5Mo-5V-3Cr alloys during hot deformation. Materials, 12(3). doi:10.3390/ma12030457

  • Zhao, Q., Yang, F., Torrens, R., & Bolzoni, L. (2019). Comparison of hot deformation behaviour and microstructural evolution for Ti-5Al-5V-5Mo-3Cr alloys prepared by powder metallurgy and ingot metallurgy approaches. Materials and Design, 169. doi:10.1016/j.matdes.2019.107682

  • Bolzoni, L., & Hari Babu, N. (2019). Towards industrial Al-Nb-B master alloys for grain refining Al-Si alloys. Journal of Materials Research and Technology. doi:10.1016/j.jmrt.2019.09.031

This page has been reformatted for printing.