The University of Waikato - Te Whare Wānanga o Waikato
Home Waikato Home > Science & Engineering > Research Staff + Student Login

Research Publications for Mingtu Jia

Research is a vital function of the Waikato's School of Science and Engineering. There are many active research groups within the School, spanning a wide range of topics.

Author's Publications

Publications ByJIA, Mingtu

  Use our Online Phonebook to contact our current staff members.

  • Jia, M., Blanchard, C., & Bolzoni, L. (2018). Microstructure and mechanical properties of Ti-5Al-2.5Fe alloy produced by powder forging. Key Engineering Materials, 770, 39-44. doi:10.4028/

  • Jia, M. T., Gabbitas, B., & Bolzoni, L. (2018). Evaluation of reactive induction sintering as a manufacturing route for blended elemental Ti-5Al-2.5Fe alloy. Journal of Materials Processing Technology, 255, 611-620. doi:10.1016/j.jmatprotec.2018.01.013

  • Liang, J. M., Zhang, Z., Jia, M. T., Cao, L., Li, C. G., Gao, H. Y., . . . Zhang, D. L. (2018). The microstructures and tensile mechanical properties of ultrafine grained and coarse grained Al-7Si-0.3Mg alloy rods fabricated from machining chips. Materials Science and Engineering: A, 729, 29-36. doi:10.1016/j.msea.2018.05.047

  • Bolzoni, L., Dougherty, T., Safar, S., Pal Singh, A., Jia, M., Yang, F., & Xu, Y. (2018). Titanium-silicon nitride fibre composites made with hot-press and pressure-less sintering. In Advances in Powder Metallurgy and Particulate Materials - 2018: Proceedings of the 2018 International Conference on Powder Metallurgy and Particulate Material, POWDERMET 2018 Vol. 2018-June (pp. 609-618). Conference held San Antonio, USA.

  • Jia, M., Zhang, D., Liang, J., & Gabbitas, B. (2017). Porosity, microstructure, and mechanical properties of Ti-6Al-4V alloy parts fabricated by powder compact forging. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 48(4), 2015-2029. doi:10.1007/s11661-017-3965-5

  • Jia, M., & Gabbitas, B. (2016). Powder consolidation of titanium and titanium alloys by a powder compact forging process. In Key Engineering Materials Vol. 704 (pp. 68-74). doi:10.4028/

  • Jia, M. T., Liang, J. M., Zhang, D. L., Kong, C., & Gabbitas, B. (2016). Effects of holding time during pre-sintering and post-forging annealing on the microstructure and mechanical properties of Ti parts fabricated by powder compact forging. Materials Science and Engineering A: Structural Materials: Properties, Microstructure and Processing, 655, 113-121. doi:10.1016/j.msea.2015.12.079

  • Jia, M., & Gabbitas, B. (2015). Rapid Synthesis of a Near-β Titanium Alloy by Blended Elemental Powder Metallurgy (BEPM) with Induction Sintering. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 46(10), 4716-4729. doi:10.1007/s11661-015-3048-4

  • Jia, M. T., Zhang, D. L., Zhang, D. L., Gabbitas, B., Liang, J. M., & Kong, C. (2015). A novel Ti-6Al-4V alloy microstructure with very high strength and good ductility. Scripta Materialia, 107, 10-13. doi:10.1016/j.scriptamat.2015.05.008

  • Jia, M., & Zhang, D. (2015). Warm compaction of titanium and titanium alloy powders. In Titanium Powder Metallurgy: Science, Technology and Applications (pp. 183-200). doi:10.1016/B978-0-12-800054-0.00011-3

This page has been reformatted for printing.